 |
Categories |
 |
|
 |
Information |
|
|
|
Quick Find |
|
|
|
Languages |
|
|
|
|
|
| |
Product Name+ |
 |
1) Funktionsbeschreibung Digitale Telemetry
| ONLY IN GERMAN! Sollen mehrere Kanäle nach der beschriebenen, analogen FM-Technik übertragen werden, müssen mehrere unterschiedliche Trägerfrequenzen und eben so viele selektive HF-Empfänger verwenden werden, was das Kosten/Nutzen-Verhältnis unverhältnismäßig vergrößern würde. Die Lösung des... More>>> |
|
 |
CT2-Wheel Telemetry -NEW!!
| 2-Channel wheel telemetry system for connection with strain gages, force, temperature and vibration sensors as well as high level input +/-5 or +/-10Volts. · 4 different carrier frequencies (433.3, 433.7, 434.1 or 434.5 MHz) enable measurements at 4 Wheels for one car. · A mixed installation of... More>>> |
|
 |
CT4/8-Wheel
| 4 (8) Channel wheel telemetry system for connection with strain gages, force, temperature and vibration sensors as well as high level input +/-5 or +/-10Volts. · 4 different carrier frequencies (433.3, 433.7, 434.1 or 434.5 MHz) enable measurements at 4 Wheels for one car. · A mixed installation of... More>>> |
|
 |
KMT-CLS Measurement Steering Wheel Sensor MSW NEW!!
| Steering effort sensor - The new KMT-CLS measurement steering wheels sensor is designed for applications in any car or commercial vehicle steering system. The KMT-CLS sensor is available with a torque range of ±100Nm and ±200Nm, the range for the steering angle is ±1340°. At the CAN output in... More>>> |
|
 |
RPM-8000-OBD2 - NEW!!
| RPM8000-OBD2 RPM and SPEED measurement in cars via CAN “On-Board Diagnostics” interface with analog and pulse outputs RPM8000-OBD2 offers a discerning solution for automotive RPM measurement without an additional sensor. The information will read direct from the CAN-OBD2- interface (ISO 15765 CAN,... More>>> |
|
 |
RPM-8000-PRO
| Offers a discerning solution for automotive RPM measurement without an additional sensor. Independent of vehicle and engine type, No sensor installation required, Direct reading of RPM via LCD, Wide dynamic range, Analoge and digital output, Small, lightweight, convenient, Simple and accurate... More>>> |
|
 |
TEL1-PCM Torque Telemetry New!!
| Digital one channel telemetry system for strain gage applications on rotating shafts “Controlled Gain and AZ at receiver side” ,Signal bandwidth up to 1200Hz (-3dB),Distance transmitting coil to receiving head 25mm (Optional 35mm),Powering transmitting side : Inductive
... More>>> |
|
 |
TEL1-PCM-BATT Torque Telemetry
|
Digital one channel telemetry system (transmitter battery-powered) for strain gage applications on rotating shafts “Controlled Gain and AZ at receiver side” ,Signal bandwidth up to 1200Hz (-3dB),Distance transmitting coil to receiving head 150 mm, Powering via battery 6-9V
... More>>> |
|
 |
TEL1-PCM-HS High Speed Telemetry
| Digital one channel "HIGH SPEED" (50kHz) telemetry system for strain gage and ICP applications on rotating shafts “Controlled Gain and AZ at receiver side” Signal bandwidth up to 50,000, Distance transmitting coil to receiving head 20 mm (Optional35mm), Powering transmitting side : Inductive,... More>>> |
|
 |
TEMPTEL8 Wheel Telemetry - NEW!!
| Small 8 channel Telemetry for Thermocouples K or J ·12 bit resolution, simultaneous sampling of all channels, Full galvanic isolated inputs, Cold junction compensation, Bandwidth 8x 0-30Hz, Output is linearised for K or J, +/- 10V analogue output at the receiver side, Distance up to 10m between... More>>> |
|
| Displaying 1 to 10 (of 10 products) |
Result Pages: 1 |
|
|
|
News |
|
|
|
Who's online? |
|
|
There currently are
9 guests
online. |
|
|
|
|
